1/13/2024 0 Comments Proselect thermostat psts11npDC Power: 3.0 Volt DC (2 AA Alkaline batteries included).Electrical Rating: 24 Volt AC (18-30 Volt AC) 1 amp maximum load per terminal 2 amp total maximum load (all terminals) (PSTS11P52) 3 amp total maximum load (all terminals) (PSTS21P52).Specifications Installation Testing Your New Thermostat Programming User Settings Temperature Adjustment Additional Operation Features Battery Replacement Troubleshooting Wiring Diagrams 1 2 3 4 5 6 7 8 9 1 Specifications Any other use is not recommended and will void the warranty. This thermostat should only be used as described in this manual.This thermostat also requires two (2) properly installed “AA” alkaline batteries to retain clock setting in the event of loss of AC Power due to a power outage or rolling blackouts when used as a hardwired thermostat.Refer to “Low Battery Detection and Replacement” section for more information. This thermostat is a dual power thermostat and either requires 24 Volts AC Power or two (2) properly installed “AA” alkaline batteries for normal operation and control of the heating or cooling system.Always turn off power to the air conditioning or heating system prior to installing, removing, cleaning or servicing thermostat.Builder Series Programmable Thermostats Single Stage 1 Heat / 1 Cool Conventional and Heat Pump Multi-Stage 2 Heat / 1 Cool Conventional and Heat Pump WARNING Important Safety Information 2 3 4 1 Installing New Thermostat Replacing Existing Thermostat WARNING! Read BEFORE Testing Default Thermostat Settings Setting Thermostat User Options Setting Current Time of Day and Day of Week 5 6 8 Setting the Extended Hold Time (see also section 6) cont. The Temporary Program Override will reset when the next set point time occurs or after four hours–whichever comes first. The program indicator ( MORN, DAY, EVE or NIGHT ) will be flashing in the display, indicating that a Temporary Program Override is in effect. The display will return to normal operating mode after 15 seconds or you can press the RETURN button. Release the or button and press the or button again as desired to adjust the set temperature. The entire display will flash once and the SET indicator will be displayed. Press and hold or button for 1 second or longer. Continuing to hold the or button for 1 second or longer will allow the user to temporarily override the current programmed set point. The display will return to normal operating mode when the or button is released. The current set point temperature will be displayed in place of the current room temperature, and the indicator SET will be displayed. This will return all thermostat settings to their default values. NOTE: To erase all entered programs, current time of day, day of week and other user settings, gently press the RESET button using a paper clip or a small pencil tip. Follow steps 2 through 8 to program the set point times and temperatures for the Weekday and Weekend groups in the COOL mode. Place the system switch in the COOL mode of operation. Follow steps 3 through 5 to set the set point times and temperatures for the MORN, DAY, EVE and NIGHT set points for the Weekend group in the HEAT mode. The hour portion of the MORN set point time and the AM/PM indicator will be flashing. The display will show SA, SU to indicate the Weekend group is being programmed. After pressing the PROG button, you will enter the Weekend Program Group. Follow steps 3 through 5 to set the set point times and temperatures for the MORN, DAY, EVE and NIGHT set points for the Weekday group in the HEAT mode. Again, you will see the hour portion of the set point time and the AM/PM indicator will be flashing. The thermostat will now display the DAY set point time and temperature. Press the or button to change the set point temperature to the desired setting in 1˚ F increments (0.5˚ C). The temperature digits will begin flashing. Press the or button to change the time to the desired minute in 10-minute increments. The minute portion of the set point time will begin flashing. Press the or button to change the time to the desired hour in 1 hour increments.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |